Came Ati-P324 Kit Manual do Utilizador

ATI KITCAME UNITED KINGDOM LTDORCHARD PARK INDUSTRIAL ESTATETOWN STREET, SANDIACRE,NOTTINGHAM, NG10 5BPTEL: 0115 921 0430FAX: 0115 921 0431INTERNET -

9STAGE 2 - WIRING & ELECTRICAL2.1 - Fitting the Control Panel in the Casing

102.2 - Gaining Access to the MotorsTO GAIN ACCESS TO THE MOTOR TERMINALS AND WORM DRIVE FIRSTREMOVE THE COVERS. FIRST REMOVE THE SCREWS FROM THE TO

WITH THE COVERS REMOVED INSTALL THE MOTOR ON THE TWOBRACKETS AND SECURE THE MOTOR WITH THE NUTS AND BOLTSPROVIDED.Fig 9M8 X 50M8 X 10WORM-GEARM8 LOCKN

12MOVE THE GATE TO THE DESIRED OPEN POSITION. LOOSEN THE SCREWSWHICH HOLD THE MICROSWITCH IN POSITION. SLIDE THE MICROSWITCHON THE SUPPORT PLATE UNT

13U V W X Y E E3 U V W W X YMOTOR 1 MOTOR 2MOTOREARTHMOTOREARTH2.5 - Wiring the MotorsE

ZA42.6 - Wiring in the Safety PhotocellsSAFETY BEAMS SHOULD BE FITTED APPROXIMATELY15 INCHES FROM GROUND LEVELCONTROL PANEL10 11

2.8 - Wiring in the Tuned Antenna2.9 - Coding the Remote Controls1. REMOVE THE BATTERY COVER & CASING OF THE REMOTE CONTROLHANDSET TO REVEAL THE D

END OF INSTALLATIONSTAGE 2BEFORE STARTING STAGE 3 -Commissioning the Control PanelPLEASE CHECK THAT YOU HAVE CORRECTLY:Ref Page1. GAINED ACCESS TO M

STAGE 3COMMISSIONING THE CONTROL PANEL3.1 - Initial Wiring & Control Panel Setup1. CONNECT POWER TERMINALS L1 - L2AND A SUITABLE EARTH (L2 BEING L

3.2 - Opening & Closing the Gates2. ONCE YOU HAVE PROVED THEMOTOR DIRECTION USETERMINALS 2 & 7 TO OPEN ANDCLOSE THE GATES WITH ATRAILING WIRE

THESE INSTRUCTIONS WILL SHOW YOU HOW TO INSTALLAN ATI GATE KIT TO A PAIR OF GATES.PLEASE READ THESE INSTRUCTIONS AND DIAGRAMSCAREFULLY BEFORE STARTING

TRIMMER TR2M3.3 - Control Panel AdjustmentsTRIMMER TL1. TO DELAY ONE GATE LEAF, ADJUST POTENIOMETER TR2M TO DELAYTHE CLOSING OF GATE NO. 2 IN THE CLO

10 11 1 2 3 5 7 C110 11 C NC3.4 - Automatic Close & Activating Safety PhotocellsFULLY ANT

3.5 - Programming the Remote Controlsto the Control PanelTo use the remote control system, proceed as follows:A) Turn power OFF and insert AF radio fr

22PLEASE CHECK THAT YOU HAVE CORRECTLY:Ref Page1. SET POWER SETTING, SET DIPSWITCHES FORCOMMISSIONING, ENSURE WIRE LINKIS FITTED BETWEEN TERMINALS

234. TROUBLESHOOTING GUIDEA MULTIMETER WILL BE NEEDED PROBLEM SOLUTIONGATE WILL NOT RESPONDWHEN GIVEN A COMMAND 1. CHECK POWER SUPPLY TO THE

24PROBLEMSOLUTION 1. AF FREQUENCY CARD NOT FITTED TOCONTROL PANEL. 2. REMOTE CONTROL HAS NOT BEENPROGRAMMED INTO THE CONTROLPANEL. 3. REMOTE CONTRO

88mm933mm880mm500mmTravel126mmPILLARAHINGEGATE WINGCLOSEDCENTRESTOPECB255. TECHNICAL INFORMATION5.1 - Technical SpecificationTYPE130 DEGREESA mm B mmC

265.2 - Motor Torque SettingsTo vary the motor torque, move the indicated spade connector to one of thefour position : 1=min, 4=max.N.B. It is always

275.3 - ZA4 Control Panel DescriptionDescription of Control Panel:Micro-processor controlled electrical cabinet powered by 230V (a/c) at50-60Hz, singl

281 CONTROL PANEL1 FREQUENCY CARD2 ATI MOTORSTUNED ANTENNA2 REMOTE CONTROLTRANSMITTERS1 PAIR SAFETYBEAMSFig 29Other functions available:Automatic clos

INSTALLATION INSTRUCTIONSCONTENTS1) Stage 1:- Civil & Mechanical Section Page1.1 BASIC HINGE GEOMETRY 31.2 BASIC CABLE LAYOUT 41.3 LOW VOLTAGE

5.4 - ZA4 Wiring DiagramTerminals 1 and 2, 2 and C1 are normally closed circuits and ifthey are not used they must be linkedL1 L2 U V W

30ZA45.5 - Control Panel AdjustmentsFig 25Trimmer T.L. - Adjustment of operating time from a minimum of 0 seconds to amaximum of 120 seconds N.B. it i

31L1 L2 U V W X Y E1 10 11 1 2 3 5 7 C1L1L2UWVXWYWE110510111223272C15.6 - Elec

Notes

Notes

Notes

6. CONTACT INFORMATIONTHIS INSTALLATION WAS COMPLETED BY:...NAME...

3STAGE 1CIVIL & MECHANICAL SECTION1.1- Basic Hinge GeometryBEFORE BEGINNING YOUR INSTALLATION OF YOUR ATI SYSTEM, CHECK THEFOLLOWING:* YOUR GATE P

1.2 - Basic Cable LayoutTHIS DIAGRAM DETAILS THE BASIC CABLE LAYOUT FORA PAIR OF MOTORS.THE POWER SUPPLY TO THE CONTROL PANEL SHOULD BE LIVE ANDPROTEC

51.3 - Low Voltage Cable LayoutALL CAME ACCESSORIES CAN BE WIRED 0.2m STRANDED CABLE (BUGLARALARM TYPE). THE TUNED ANTENNA SHOULD BE WIRED WITH COAXI

6THE REAR BRACKET IS EQUIPPED WITH ADDITIONAL HOLES TO MAKEINSTALLATION OF THE GATE MOTOR EASIER, OR TO CHANGE THEOPENING ANGLE OF THE GATE. THE REAR

7WITH THE GATE IN THE FULLY CLOSED POSITION WELD THE FRONTBRACKET TO THE FIXING PLATE THEN ATTACH IT TO THE GATE. THEANCHOR PLATE MUST BE HORIZONTALL

BEFORE STARTING STAGE 2 - Wiring & ElectricalPLEASE CHECK THAT YOU HAVE CORRECTLY:Ref Page1. PREPARED THE CABLING CORRECTLY 1.2 42. CORRECTLY ATT